To ensure your brakes are always at their best, we offer a unique brakes lifetime guarantee. What Causes A Ford Focus Brake Lamp Bulb Fault. This means removing the screws that hold your lamp in place and unplugging hte connector on your bulb. If the pads wear out, the brake warning light can come on. Brake disc thickness should be measured if they are at or below the manufacturer's safe minimum thickness specification they should be replaced. On most cars, it is found directly in front of the driver's side of the car. First, it is important to determine the cause of the problem, so you can address it appropriately. The braking system amplifies the force of your foot on the pedal with a system of lines filled with hydraulic brake fluid. Our technicians will quickly get to the bottom of your brake warning light and fix the problem, whether it's a faulty sensor or a severe fluid leak. Think of how much time you spend with your foot on the brake, and then consider that the brake light bulbs have to be illuminated during that entire period. A car's braking system has sensors monitoring fluid level, E -brake position, and in some cases brake pad life.
Otherwise, you will never be able to use your brake lamp bulb at all. As best practice for drivers whose annual mileage is considered average or high (around 8, 000 miles per year or more), Kwik Fit recommend that your vehicle's braking system is checked at least twice a year. Brake Checks and Replacement at Kwik Fit. The first and easiest thing to check is your emergency brake. If you keep these tips in mind, most brake light problems will be easy to diagnose and fix on your own.
For safety's sake, it's important to have your vehicle inspected as quickly as possible when you notice any of the above symptoms. A failed sensor can trigger the brake warning light. Replacing brake lights is cheap and easy to do, most of the time, with a basic set of tools. I currently contribute as an editor to several online and print automotive publications, and I also write and consult for the pharmaceutical and medical device industry. The reservoir has a sensor that triggers the brake warning light when the fluid level falls too low. For instance, it could be due to bad brake switches, faulty relays or modules, or defects to your light bulbs. Replacing one brake disc or drum could cause an imbalanced braking performance that could lead to further premature wear. Using the fuse diagram on the box's cover (or in the manual), find the fuse for the brake circuit and make sure it hasn't been blown. For example, a set of brake pads could last up to 60, 000 miles or more on a car driven mostly on the motorway. Your brake lights only turn on when you press on the brake pedal. Replacing your pads will turn off the lights. 0 TDCi Titanium Auto Quote Link to comment Share on other sites More sharing options... Pulsating - If you feel a continuous pulsating from the brake pedal whenever you apply the brakes, this indicates the brake disc has become warped due to excessive heat.
Information from the computer and professional examination is needed to determine the cause of the problem. The switch signals your brake light bulbs, so these will turn on the moment the brake pedal is stepped on. The light warns the driver of an issue, but further investigation is needed to determine the cause of the problem. When do I need a brake inspection?
Add brake fluid to the reservoir if it's low. Most drivers worry when they see a check engine light, but the brake warning light is arguably more concerning. Photo courtesy of Morguefile. This means that the driver behind you is not aware that you are braking, which can be a big safety risk. Having been bitten by the car bug at a young age, I spent my formative years surrounded by Studebakers at car shows across Quebec and the northeastern United States. Over ten years of racing, restoring, and obsessing over automobiles lead me to balance science writing and automotive journalism full time. Squeaking - there are many reasons why brakes squeal. There are a number of tell-tale signs to look out for when using your brakes. A brake pedal that is soft and can be applied all the way to the floor usually means the brake fluid is ineffective and needs replacing but there can be several other potential reasons such as a master cylinder fault. There are two terminals, as well as a metal stripe, and these run through your terminals. You can find these in the central units of your brake system. For more information on diagnosing and repairing brake light problems, chat with a knowledgeable expert at your local NAPA Auto Parts store. By far, a burnt out bulb is one of the brake light problems that crops up the most, and it's easy to understand why.